16810HPS Thin + short drive shaft Right drive shaft VW Golf 4 IV 6 speed switch
MAPCO 16810HPS Thin + short drive shaft, right-hand drive shaft, VW Golf 4, Bora, 6-speed switch, Audi A3 8L
The car drive/cardan shaft is used to transmit power between the gearbox and the driven wheel and is part of the drive train. Cardan shafts consist of the cardan shaft tube with sliding piece and the joints. Two-part cardan shafts are often used. The division of the cardan shaft ensures low-vibration operation and prevents noise. Cardan shaft damage occurs when the sleeves are damaged. The typical damage pattern shows traces of grease, particularly on the front vehicle doors, which are thrown out by the torn sleeve when the steering is fully turned. Penetrating water emulsifies with the grease; dirt also causes wear on the sliding surfaces of the joint. Signs of incipient damage can also be cracking noises when the load changes. Porous sleeves should be replaced soon.
Article information:
Installation side: front axle right
Length: 796.0 mm
Bore diameter: 10.2 mm
Thread size: M20x1.5
External toothing wheel side: 36
Number of bores: 6
Bore circle diameter: 94 mm
Joint diameter wheel side: 98 mm
Joint diameter gearbox side: 108 mm
Chassis: for vehicles with lowered chassis
Suitable for the following vehicles:
AUDI A3 (8L1) 1.9 TDI
VW GOLF IV (1J1) 1.9 TDI
VW GOLF IV Variant (1J5) 1.9 TDI
SEAT LEON (1M1) 1.9 TDI
VW BORA Variant (1J6) 1.9 TDI
SKODA OCTAVIA I Combi (1U5) 1.9 TDI
SEAT LEON (1M1) 1.8 20V T
VW GOLF IV (1J1) 1.8 T GTI
VW BORA (1J2) 1.9 TDI
VW GOLF IV Variant (1J5) 1.9 TDI 4motion
VW BORA Variant (1J6) 1.9 TDI 4motion
SEAT TOLEDO II (1M2) 1.9 TDI
SKODA OCTAVIA I (1U2) 1.9 TDI
SEAT LEON (1M1) 1.8 T Cupra R
VW BORA Variant (1J6) 1.8 T
VW BORA (1J2) 1.8 T
SEAT TOLEDO II (1M2) 1.8 20VT
VW BORA (1J2) 1.9 TDI 4motion
If the car is not listed, please send a copy of the vehicle registration document by email to shop@schalk-tuning.de before ordering or at least the chassis number and KBA numbers or please call us beforehand: 03476 813028.
The car drive/cardan shaft is used to transmit power between the gearbox and the driven wheel and is part of the drive train. Cardan shafts consist of the cardan shaft tube with sliding piece and the joints. Two-part cardan shafts are often used. The division of the cardan shaft ensures low-vibration operation and prevents noise. Cardan shaft damage occurs when the sleeves are damaged. The typical damage pattern shows traces of grease, particularly on the front vehicle doors, which are thrown out by the torn sleeve when the steering is fully turned. Penetrating water emulsifies with the grease; dirt also causes wear on the sliding surfaces of the joint. Signs of incipient damage can also be cracking noises when the load changes. Porous sleeves should be replaced soon.
Article information:
Installation side: front axle right
Length: 796.0 mm
Bore diameter: 10.2 mm
Thread size: M20x1.5
External toothing wheel side: 36
Number of bores: 6
Bore circle diameter: 94 mm
Joint diameter wheel side: 98 mm
Joint diameter gearbox side: 108 mm
Chassis: for vehicles with lowered chassis
Suitable for the following vehicles:
AUDI A3 (8L1) 1.9 TDI
VW GOLF IV (1J1) 1.9 TDI
VW GOLF IV Variant (1J5) 1.9 TDI
SEAT LEON (1M1) 1.9 TDI
VW BORA Variant (1J6) 1.9 TDI
SKODA OCTAVIA I Combi (1U5) 1.9 TDI
SEAT LEON (1M1) 1.8 20V T
VW GOLF IV (1J1) 1.8 T GTI
VW BORA (1J2) 1.9 TDI
VW GOLF IV Variant (1J5) 1.9 TDI 4motion
VW BORA Variant (1J6) 1.9 TDI 4motion
SEAT TOLEDO II (1M2) 1.9 TDI
SKODA OCTAVIA I (1U2) 1.9 TDI
SEAT LEON (1M1) 1.8 T Cupra R
VW BORA Variant (1J6) 1.8 T
VW BORA (1J2) 1.8 T
SEAT TOLEDO II (1M2) 1.8 20VT
VW BORA (1J2) 1.9 TDI 4motion
If the car is not listed, please send a copy of the vehicle registration document by email to shop@schalk-tuning.de before ordering or at least the chassis number and KBA numbers or please call us beforehand: 03476 813028.
Autopartner GmbH
Gregor-von-Brück-Ring 1
14822 Brück
Telefon: +49 33844 67 91 80
E-Mail: info@autopartner24.de
https://www.autopartner24.de